DIY-Do-It-Yourself-Self-Installed Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project: A Guide-Step-By-Step Manual-Comprehensive Handbook
DIY-Do-It-Yourself-Self-Installed Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project: A Guide-Step-By-Step Manual-Comprehensive Handbook
Blog Article
Presented here below you can get a bunch of brilliant insight related to How to Install or Replace a Shower Drain.
Updating a shower room is among the much more popular home renovation tasks. Dealing with the plumbing for draining your shower can be exceedingly straightforward unless you overdo it.
Handling Your Own Shower Drain Installment Project
Whether you are a bathtub or shower individual, the majority of people seek shower only options when acquiring a residence. This basic truth means more than a few house owners invest a weekend upgrading or setting up showers in their bathrooms. Thankfully for you, it is a fairly straightforward process.
A collection agency or pan refers to the straight surface area located at the end of the shower. The collector usually contains a non-slip surface area a little banked towards the center or anywhere the drain is located. Integrated with 3 to 4 inch walls around the side, the objective of your shower water drainage plumbing is to get the water to move to and down the tubes.
You can literally develop a collection agency for your new shower, however you really need to think about it. Do you really want to enter into the difficulties of obtaining the sloping correct, and also ensuring every facet of it is water resistant? And I mean every aspect! It is much easier to simply purchase a pre-cast collection agency online or at your local Lowes, Home Depot or hardware shop. Structure one may sound like a wonderful suggestion, however you will most likely feel in different ways after a number of hours.
No matter just how you set about getting a frying pan, you need to strive to use one that has the drain situated in the exact same spot as the initial frying pan. Moving the drain pipelines can be a task, particularly if the building contractor utilized a distinct framework framework. If you are identified to relocate the drainpipe, you are going to need to cut down the pipe or extend it, which may mean destroying big chunks of the flooring. Put another way, you are mosting likely to be taking a look at a numerous weekend break project.
Thinking we have our drain aligned, the actual hook up is rather easy. The water drainage pipe need to be facing upright up to the enthusiast. It will usually appear like a "U", which suggests it serves as a cleanout to maintain nasty scents from coming back up from the drainpipe. To connect the drain, you are mosting likely to create a water tight link between a drainpipe cap on the top of the pan and the water drainage pipe. Equipments vary, however you are commonly going to do this by placing a combining piece on the top of the drain pipeline. This is then covered with gaskets and also literally screwed right into the drainpipe cap. The drain cap must act as a locknut, to wit, it screws directly onto the combining.
The complicated part of this procedure is getting your drainpipe cap to fit into a leak-proof placement in the pan. This is achieved by backing off the drainpipe cap once you make sure every little thing fits together. At that point, you put plumbers putty around the underside of the cap and afterwards screw it back on. The putty should form a tight seal in between the cap and also the shower frying pan, which keeps water from dripping under it and also into the mounting under the shower.
Obviously, washroom showers been available in a wide range of styles nowadays. If you purchase a collection agency, they generally included plumbing guidelines or the shop can keep in mind anything uncommon you need to know. It sounds complex, however is normally rather easy. Enjoy!
Things to Know Before Installing a Shower Drain
Replacing a shower drain isn’t usually a difficult task, but it always pays to be prepared for complications before you start the job, especially as every project is different. While it should take just a couple of hours to replace a drain in a preformed shower base, you’ll want to allow yourself additional time and a flexible toolbox.
“As the age of the shower increases, so does the likelihood of problems during installation,” says Daniel O’Brian, the technical expert for leading online plumbing retailer SupplyHouse.com. Over time, older metal drains can corrode, making them very difficult to remove, and you can even run into problems with installations in newer showers if access to the drain is restricted. No matter what challenges you face, the following tips will help the project go a little more easily.
Prepare for pipe size discrepancies.
The majority of shower drainpipes are two inches in diameter, but if you have two-inch drains and you run into a three-inch drainpipe, you’ll be making another trip to the plumbing supply store. “Always check with local codes,” O’Brian suggests. “The larger drain size minimizes the chance of a shower overflowing.” And if you keep a supply of size-adaptable shower drains on hand, such as the Oatey 2-Inch or 3-Inch PVC Shower Drain, the size discrepancy won’t slow you down at all. This weld-type drain fits either a two- or three-inch drainpipe. With a two-inch drainpipe, the body of the drain fits over the pipe; with a three-inch pipe, it fits inside. If your home has three-inch drainpipes, it pays to pick up a box of size-adaptable drains to have on hand.
Assume you’ll have to cut through the ceiling.
In most cases, you won’t be able to avoid cutting through the ceiling below the shower to gain access. “If a leak is present, you’ll probably have to replace the drywall on the ceiling below as well as the drain, and you should take care of it as soon as possible to minimize damage,” O’Brian says. Drywall replacement is a relatively simple home repair project, so cutting a hole in the ceiling shouldn’t be a major concern. Alternatively, you can cover the hole with a return-air grill that can be easily removed if you need to access the plumbing at a future date.
The only time you won’t need to cut through the ceiling below the shower is when you’re replacing both the drain and the shower base. In that case, start by pulling out the old shower pan and removing the old drain. Then, connect the body of the new drain to the new shower base, and set the shower base in place according to the manufacturer’s specifications. Be warned: Balancing the shower base while you align the drain body over the pipe will almost certainly require the help of an additional person.
The best type of drain for this situation is often called a “compression,” or “friction,” drain, such as this Oatey 2-Inch PVC No-Calk Shower Drain, which features a rubber gasket inside the drain body. Remove the gasket before the shower base is set. After the shower base is set, lubricate the gasket with plumber’s soap and slide it into place between the drain body and the pipe. Tighten the compression nut inside the drain body with a screwdriver to seal the connection, then snap the strainer into place. Being able to remove the gasket before you set the shower base gives you a little more room to maneuver—remember, you’re balancing the shower base while you’re trying to fit the connected drain body over the pipe in the floor.
Tight spots spell trouble.
It doesn’t happen often, but occasionally when you cut through the ceiling below the shower you find wiring or pipes that prevent you from getting your water pump pliers firmly on the nut that connects the drain to the pipe. (These additional wires, pipes, and even ductwork would have been added after the shower was installed.) If you can’t find a way to remove the nut or reach the pipe to cut it below the drain, you may end up having to pull the shower base out so you can access the drain from the top. Then, just like that, what should have been a simple drain replacement turns into a major project.
While you may be stuck with this unanticipated problem, you can prevent it from happening in the future by installing an outer locknut-style drain, such as the Sioux Chief 2-Inch JackRabbit Shower Drain .
Unlike standard drains that solvent weld or attach with a nut, the JackRabbit drain attaches via four jacking screws from below. (It’s usually much easier to get a screwdriver in a tight spot where bulky water pump pliers won’t fit.) The drain body features a push-on compression gasket that attaches to the drainpipe without the need for caulking. After the shower base is set, tighten the jacking screws from below to suck the flange downward until it seals against the shower floor.
Sometimes it’s easier to replace the whole trap.
Whenever you’re installing a shower drain with welded connections, you have to cut the drainpipe to remove the old drain. While this is necessary, it leaves you with a shortened drainpipe that you’ll need to extend before you can install the new drain. Trying to extend the pipe while you’re working overhead in a tight space is both time-consuming and physically challenging, so it’s often quicker (and simpler) just to cut out the entire drain trap and replace it. To install another weld-type drain, such as this 2-Inch Sioux Chief PVC Drain, you’ll want to assemble and dry fit all the connections before you glue them together. Be sure the angle of fall on the horizontal drain pipe remains the standard ¼ inch per linear foot.
Take care not to block weep holes.
Installing a new drain in a tiled shower is another scenario that often necessitates replacing the entire shower floor. Tiled showers rest on a mortar bed laid over a waterproof membrane (such as the Oatey 5’ x 6’ PVC Shower Pan Liner) that’s installed over yet another mortar bed. Because of this construction, a cemented-in shower drain cannot be replaced unless the tiles and the mortar around it are also removed and then reconstructed.
Tiled showers offer another complication: Because grout can crack, it’s important to have a backup plan to catch any water that might leak through. For that reason, shower drains designed for installation in tiled showers should have weep holes in their middle section to direct any water that reaches the membrane into the shower drain. These applications require a drain that has weep holes, such as the Oatey 2-Inch or 3-Inch PVC Shower Drain. To install, attach the base of the three-part drain to the drainpipe before the first mortar bed is smoothed into place. Then, install the membrane over the mortar bed (and over the drain base) and cut out a section over the drain hole in order to attach the center part of the drain, on which the weep holes are located. Make sure the section with the weep holes does not get clogged with mortar. To ensure that water will be able to flow through the weep holes, place several handfuls of pea gravel around the base of the exposed drain to protect it from the next layer of mortar. If you take these precautions, once the shower floor has been tiled, any water that makes its way to the membrane will exit through the weep holes and down the drain rather than leak out elsewhere.
https://blog.supplyhouse.com/5-things-to-know-before-installing-a-shower-drain/
Hopefully you enjoyed our topic about How to Install or Replace a Shower Drain. Thank you so much for finding the time to read through our posting. Sharing is caring. Helping people is fun. Bless you for your time. Come back soon.
Report this page